TRAINING ELECTRICAL MAINTENANCE LOW AND MEDIUM VOLTAGE

TRAINING ELECTRICAL MAINTENANCE LOW AND MEDIUM VOLTAGE

Deskripsi Training Electrical Maintenance Low and Medium Voltage

The backbone of many electric power systems is the medium voltage distribution system. Typically operating at voltages ranging from 2,400 to 34,500 Volts, voltage stress, corona, surges and protection of equipment all create unique challenges in design, equipment selection, operation and engineering. This 2 day class takes you through the basics of medium voltage power systems including components,equipment, design and operation problems as well as protection of medium voltage systems.

Materi Training Electrical Maintenance Low and Medium Voltage

  1. INTRODUCTION
  2. MEDIUM VOLTAGE SAFETY
    • Electrocution at Low vs. Medium Voltage, Arc Flash,
    • Qualified Person, Approach Boundaries
  3. TYPES OF MEDIUM VOLTAGE SYSTEMS
    • Utility and Industrial One lines, Reliability Requirements,
    • Overhead and Underground Systems, Regulated Systems
  4. MEDIUM VOLTAGE CABLE
    • Copper vs. Aluminum Design, Voltage Ratings
    • Insulation Ratings, 100%, 133%, 173% Insulation Levels,
    • Shielding Requirements, Electric Fields, Terminating MV
    • Conductors, Orientation of Overhead Lines
  5. MEDIUM VOLTAGE SUBSTATION TRANSFORMERS
    1. Core and Coil Design, Aluminum and Copper Windings
    2. Tank Construction, Loss Evaluation, Efficiency, Regulation
  6. SPOT NETWORKS
    • Spot Network Design, Network Protectors, Network Protector
    • Relay Operation, Directional Protection Requirements
  7. PARTIAL DISCHARGE
    • Corona, Surface Tracking, Voltage Stress, Sensing Partial
    • Discharge, Component Failure
  8. GROUNDING MEDIUM VOLTAGE SYSTEMS
    • Resistance Grounding, Solid Grounding, Ungrounded Delta
    • Charging Current, Effect of Ground Faults on Delta Voltage
  9. SURGE PROTECTION
    • Lightning and Switching Surges, Classes of Surge Arresters
    • MCOV Ratings – (Maximum Continuous Operating Voltage)
    • TOV – (Maximum Temporary Over Voltage Capability),
    • Protective Characteristics, Surge Arrester Selection, Energy
    • Capability, Effect of Grounding on Arrestor Selection,
    • Insulation Coordination,
  10. CURRENT TRANSFORMER APPLICATIONS
    • Ratings, Selection Process, Accuracy, Saturation, Excitation
    • Curves, Burden Calculation, Momentary Ratings
  11. MEDIUM VOLTAGE CIRCUIT BREAKERS
    • Vacuum, Air, Oil, SF6 Designs, Symmetrical Interrupting
    • Rating, K-Rated Voltage Factor, Close and Latch Capability
  12. RECLOSERS
    • Application on Feeder Circuits, Recloser Settings
    • Continuous Current and Interrupting Ratings
  13. MEDIUM VOLTAGE FUSES
    • Medium Voltage Switches, Load Rating, Close and Latch
    • Rating, Short Time Rating, Expulsion vs. Current Limiting
    • Fuse Characteristics, E and R Rated Fuses, Fuse Cutouts
  14. MEDIUM VOLTAGE PROTECTION CONCEPTS
    • Medium Voltage Protection, Relays, Circuit Breakers, R and
    • E rated Fuses, Short Circuit vs. Overcurrent Protection
  15. DISTRIBUTION FEEDER PROTECTION
    • Protection with Fuses – 300%, Overcurrent Protection with
    • Relays – 600%, Short Circuit Damage Characteristics, Relay
    • “Reach” for End of Line Faults
  16. ROTATING MACHINERY PROTECTION
    • Requirements, Decrement Curves, Thermal Damage Curves,
    • Reactive, Capability Curves, Differential Protection
  17. MEDIUM VOLTAGE MOTOR CONTROLLERS
    • Protection Requirements, Motor Management Relays, Circuit
    • Breaker Protection, Relaying, Class R Rated Fuses
  18. TRANSFORMER PROTECTION
    • ANSI C57 Thru Fault Curves, Impact of Transformer Winding
    • Configuration, Overview of Differential Protection, Inrush and
    • Harmonic Restraint


PESERTA Training Electrical Maintenance Low and Medium Voltage

  • D3 atau SLTA yang berpengalaman kerja minimal 3 tahun, dan atau setara.
  • Teknisi, Operator dan Supervisor didalam bidang management kelistrikan dan atau non teknik.
  • Mereka yang dalam tugasnya berhubungan dan atau terkait dengan materi kursus.

Investasi dan Fasilitas Training

  • Harga : (dilampirkan dalam Brosur penawaran)
  • Fasilitas : Certificate, Training kits, USB 8 GB, Lunch, Coffe Break, Souvenir, City Tour
  • Untuk peserta luar kota disediakan transportasi antar-jemput dari Bandara/Stasiun ke Hotel (berlaku bagi perusahaan yang mengirimkan minimal 2 peserta) Khusus untuk training di Yogyakarta.

 

Permintaan Brosur penawaran Training ( Waktu dan Tempat) silahkan Menghubungi kami.

Catatan :

  • Pelatihan ini dapat di-customized sesuai kebutuhan perusahaan Anda bila diselenggarakan dalam bentuk In-House Training. Untuk permintaan In-House Training dengan jenis topik lainya, silahkan mengirimkan ke alamat email yang tercantum di web kami.
  • Request Training. Jika anda membutuhkan informasi pelatihan yang belum tercantum pada website ini, atau anda ingin memberikan usulan materi yang sesuai dengan tingkat kebutuhan perusahaan anda, silahkan mengirimkan ke alamat email yang tercantum.
  • Bila tidak ada tanggal dan waktu atau yang tercantum sudah kadaluarsa didalam artikel mohon tanyakan kepada kami untuk jadwal terbarunya.

Informasi Jadwal training 2016 | 2017 | 2018 | 2019 | 2020 | 2021 | 2022 | di Yogyakarta, Jakarta, Bandung, Bogor, Surabaya, Malang, Bali, Lombok, Balikpapan, Makassar, Medan, Batam, Riau, Pontianak, Semarang, Solo, Manado, dan Kota-kota lainnya

 

Informasi Jadwal Pelatihan di Indonesia

JADWAL TRAINING / PELATIHAN / DIKLAT / SEMINAR / WORKSHOP / BIMTEK 2016 – TERBARU BULAN JANUARI – FEBRUARI – MARET – APRIL – MEI – JUNI – JULI – AGUSTUS – SEPTEMBER – OKTOBER – NOVEMBER – DESEMBER 2017 Informasi Jadwal Pelatihan 2017 | 2018 | 2019 | 2020 | 2021 | 2022 | di Yogyakarta, Jakarta, Bandung, Bogor, Surabaya, Malang, Bali, Lombok, Balikpapan, Makassar, Medan, Batam, Riau, Pontianak, Semarang, Solo, Manado, dan Kota-kota lainnya